Acura CSX. Instruction — page 12


Resetting Maintenance Information Display

Resetting Individual Maintenance Items


Maintenance Minder


• The vehicle must be stopped to reset the display.
• If a required service is done and the display is not

reset, or the maintenance display is reset without
doing the service, the system will not show the
proper maintenance timing. This can lead to serious
mechanical problems because there will be no
accurate record of when the required maintenance is

• The engine oil life and the maintenance item(s) can

be only reset independently with the HDS.

1. Turn the ignition switch to ON (II).

2. Push and release the SEL/RESET button repeatedly

until the engine oil life indicator is displayed.

3. Press and hold the SEL/RESET button for about 10

seconds. The engine oil life indicator and the
maintenance item code(s) will blink, then release
the button.

NOTE: If you are resetting the display when the
engine oil life is more than 15 %, make sure the
maintenance item(s) requiring service are done
before resetting the display.

4. Press and hold the SEL/RESET button for another

5 seconds. The maintenance item code(s) will
disappear, and the engine oil life will reset to ‘‘100’’.

1. Connect the Honda Diagnostic System (HDS) to the

data link connector (DLC) (see step 2 on page 11-3).

2. Turn the ignition switch to ON (II).

3. Make sure the HDS communicates with the vehicle

and the engine control module/powertrain control
module (ECM/PCM). If it doesn’t communicate,
troubleshoot the DLC circuit (see page 11-6).

4. Select GAUGES in the BODY ELECTRICAL with the


5. Select ADJUSTMENT in the GAUGES with the HDS.


with the HDS.

7. Select RESET in the SERVICE REMINDER with the


8. Select the individual maintenance item you wish to




Maintenance Main Items


Maintenance Main Items

If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every


Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.


Replace engine oil (see page 8-10).

Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)


Replace engine oil and oil filter (see page 8-11).

Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)

Check front and rear brakes (see page 19-3).

Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.

Check parking brake adjustment (see page 19-7).

Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.

Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5).

Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.

Inspect suspension components (see page 18-3).

Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.

Inspect driveshaft boots (see page 16-4).

Check boots for cracks and boot bands for tightness.

Inspect brake hoses and lines including VSA lines (see page 19-37).

Check the master cylinder and VSA modulator-control unit for damage or leakage.

Inspect all fluid levels and condition of fluids.

Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)

Inspect exhaust system:

K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.

Inspect fuel lines (see page 11-326) and connections (see page 11-328).

Check for loose connections, cracks, and deterioration; retighten loose connections and replace
damaged parts.

NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk (

) will

not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.



Maintenance Sub Items


Maintenance Minder

Maintenance Sub Items


Rotate tires, and check tire inflation and condition.

Follow the pattern shown in the Owner’s Manual.


Replace air cleaner element (see page 11-346).

Replace every 15,000 miles (24,000 km) if the vehicle is driven in dusty conditions.

Replace dust and pollen filter (see page 21-75).

If the vehicle is driven mostly in urban areas that have high concentrations of dust, pollen, or soot in
the air, replace every 15,000 miles (24,000 km).
Replace the filter whenever airflow from the heating and air conditioning system is less than normal.

Inspect drive belt (see page 4-30).

Look for cracks and damage, then check the position of the drive belt auto-tensioner indicator.


Replace automatic transmission fluid (see page 14-232).

Capacity: 2.9 L (3.1 US qt); use Acura ATF-Z1.

Replace manual transmission fluid.

5M/T (see page 13-5), 6M/T (see page 13-82)
Capacity: 1.5 L (1.6 US qt); use Acura MTF.


Replace spark plugs (see page 4-21).

K20Z2: Use SKJ20DR-M11 (DENSO).
K20Z3: Use SK22PR-M11S (DENSO).

Inspect valve clearance (cold).

K20Z2 (see page 6-12)
Intake: 0.21

0.25 mm (0.008

0.010 in.), Exhaust: 0.28

0.32 mm (0.011

0.013 in.)

K20Z3 (see page 6-14)
Intake: 0.21

0.25 mm (0.008

0.010 in.), Exhaust: 0.25

0.29 mm (0.010

0.011 in.)


Replace engine coolant (see page 10-8).

Capacity (including the reservoir):
K20Z2: M/T 4.3 L (1.14 US gal), A/T 4.2 L (1.11 US gal)
K20Z3: 4.5 L (1.19 US gal)
Use Honda Long Life Antifreeze/Coolant Type 2.


Оцените статью
Инструкции по ремонту
Добавить комментарий