Acura CSX. Instruction — page 190

*07

19

*08

Transmission Side

Release Bearing Removal

Release Bearing Inspection

Release Bearing Installation

12-24

Clutch

A

B

C

D

E

A

D

E

B

C

(P/N 08798-9002)
1.0

1.6 g

(0.04

0.06 oz)

(P/N 08798-9002)
0.4

1.0 g (0.01

0.04 oz)

(P/N 08798-9002)
0.4

1.0 g (0.01

0.04 oz)

1. Remove the transmission; 5-speed model

(see page 13-7), 6-speed model (see page 13-84).

2. Remove the release fork boot (A) from the clutch

housing (B).

3. Remove the release fork (C) from the clutch

housing by squeezing the release fork set spring (D)
with pliers. Remove the release bearing (E).

4. Check the play of the release bearing by spinning it

by hand. If there is excessive play or noise, replace
the release bearing.

NOTE: The release bearing is packed with grease.
Do not wash it in solvent.

5. Apply super high temp urea grease (P/N

08798-9002) to the release fork (A), the release fork
bolt (B), the release bearing (C), and the release
bearing guide (D), in the shaded areas, then set the
release fork set spring (E).

08/08/21 14:42:54 61SNR030_120_0026

*09

21

12-25

A

D

E

B

C

F

B

B

A

6. With the release fork (A) slid between the release

bearing pawls (B), install the release bearing on the
mainshaft while inserting the release fork through
the hole (C) in the clutch housing.

7. Align the detent (D) of the release fork with the

release fork bolt (E), then press the detent of the
release fork over the release fork bolt squarely.

8. Install the release fork boot (F). Make sure the boot

seals around the release fork and the clutch
housing.

9. Move the release fork (A) right and left to make

sure that it fits properly against the release bearing
(B) and that the release bearing slides smoothly.
Wipe off any excess grease.

10. Install the transmission; 5-speed model (see page

13-14), 6-speed model (see page 13-91).

08/08/21 14:42:55 61SNR030_120_0027

SNR9AA70000000J1201ZAAT00

08/08/21 14:42:55 61SNR030_120_0028

01

02

*01

SNR9AA7E34116317041KBAT00

12-10

Clutch

Clutch Pedal Assembly Replacement

B

D

E

A

C

G

F

H

I

(Multipurpose Grease)

(Multipurpose Grease)

A

B

C
13 N·m
(1.3 kgf·m,
9.4 lbf·ft)

D

(Multipurpose Grease)

C
13 N·m
(1.3 kgf·m,
9.4 lbf·ft)

B
22 N·m
(2.2 kgf·m,
16 lbf·ft)

A

E

F

F

1. Disconnect the clutch pedal position switch

connector (A) and the clutch interlock switch
connector (B).

2. Pry out the lock pin (C), and pull the clevis pin (D)

out of the clevis.

3. Remove the master cylinder mounting nuts (E) and

the clutch pedal mounting bolt (F).

4. Remove the clutch pedal assembly (G).

5. Remove the clutch interlock switch (H), and the

clutch pedal position switch (I).

6. Loosely install the clutch interlock switch (A), and

the clutch pedal position switch (B).

7. Install the clutch pedal assembly (A).

8. Install the clutch pedal mounting bolt (B) and the

master cylinder mounting nuts (C).

9. Apply grease to the clevis pin (D) and the mating

surfaces of the clevis and the pedal. Slide the clevis
pin into the clevis, then install a lock pin (E).

10. Adjust the clutch pedal, the clutch pedal position

switch, and the clutch interlock switch (see page
12-8).

NOTE: Connect the switch connectors (F) after
adjusting them.

11. Check the clutch operation.

08/08/21 14:42:31 61SNR030_120_0012

Оцените статью
Инструкции по ремонту
Добавить комментарий