Acura CSX. Instruction — page 54

10

02

12

6-65

A

B

6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)

B

A

A

B

19. Connect the positive crankcase ventilation (PCV)

hose (A) (K20Z2 engine) and install the ground
cable (B).

20. Connect the fuel feed hose (A) (see page 11-331),

then install the quick-connect fitting cover (B).

21. Connect the evaporative emission (EVAP) canister

hose (A) and the brake booster vacuum hose (B).

22. Install the exhaust manifold (see page 9-11).

23. Install the intake manifold:

• K20Z2 engine (see page 9-4)
• K20Z3 engine (see page 9-9)

24. Install the drive belt (see page 4-31).

25. Install the air cleaner assembly (see page 11-345).

26. After installation, check that all tubes, hoses and

connectors are installed correctly.

27. Inspect for fuel leaks. Turn the ignition switch to

ON (II) (do not operate the starter) so that the fuel
pump runs for about 2 seconds and pressurizes the
fuel line. Repeat this operation three times, then
check for fuel leakage at any point in the fuel line.

*01

SNR9A00A14600017841KCAT00

6-66

6-66

Cylinder Head

Sealing Bolt Installation

A
22 x 1.5 mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)

B

28. Refill the radiator with engine coolant, and bleed

the air from the cooling system with the heater
valve open (see step 6 on page 10-8).

29. Do the engine control module (ECM)/powertrain

control module (PCM) idle lean procedure
(see page 11-310).

30. Do the crankshaft position (CKP) pattern clear/CKP

pattern lean procedure (see page 11-4).

31. Inspect the idle speed (see page 11-309).

32. Inspect the ignition timing (see page 4-20).

NOTE: When installing the sealing bolt (A), always use
a new washer (B).

Replace.

SNR9A000000000J0701ZCAT00

Engine Mechanical

Engine Block

……………………………………………………….

………………………………….

………………………………………………………..

…………………
…………………

………………………………………………….

……………………………

………………………………………….

…………………………………

…………………………………………..

……..

……………………………………..

………………………………………………..

……………………………

…………………………………………

………………………………………………

……………………………………………

……………………………………….

……………………………………………………….

………………………………….

………………………………………………………..

…………………
…………………

………………………………………………….

……………………………

………………………………………….

…………………………………

…………………………………………..

……..

……………………………………..

………………………………………………..

……………………………

…………………………………………

………………………………………………

……………………………………………

……………………………………….

Special Tools

. 7-2

Component Location Index

. 7-3

Connecting Rod and Crankshaft End Play

Inspection

. 7-5

Crankshaft Main Bearing Replacement

. 7-6

Connecting Rod Bearing Replacement

. 7-8

Oil Pan Removal

. 7-11

Crankshaft and Piston Removal

. 7-13

Crankshaft Inspection

. 7-15

Block and Piston Inspection

. 7-16

Cylinder Bore Honing

. 7-18

Piston, Pin, and Connecting Rod Replacement

. 7-18

Piston Ring Replacement

. 7-21

Piston Installation

. 7-23

Connecting Rod Bolt Inspection

. 7-25

Crankshaft Installation

. 7-25

Oil Pan Installation

. 7-29

Transmission End Crankshaft Oil Seal

Installation — In Car

. 7-32

Sealing Bolt Installation

. 7-33

01

01

01

SNR9A000000000J0701PAAT00

Ref. No.

Tool Number

Description

Qty

7-2

Engine Block

Special Tools

07ZAD-PNAA100

Oil Seal Driver Attachment 96

1

07746-0010700

Attachment, 24 x 26 mm

1

07749-0010000

Driver

1

Оцените статью
Инструкции по ремонту
Добавить комментарий