Acura RL. Instruction — page 180

Fig. 429: Identifying Left Side Driver’s Seat Position Sensor And Fastener With Torque
Specifications

Courtesy of AMERICAN HONDA MOTOR CO., INC.

2. Reconnect the driver’s airbag 4P connector (see DISCONNECTING SYSTEM CONNECTORS ).

3. Reconnect the negative cable to the battery.

4. Check the operation of the driver’s seat position sensor with the HDS (see DRIVER’S SEAT

POSITION SENSOR OPERATION CHECK ).

FRONT PASSENGER’S WEIGHT SENSOR UNIT REPLACEMENT

REMOVAL

1. Slide the seat all the way to the rear.

2. Disconnect the negative cable from the battery, then wait for 3 minutes before starting work.

3. Disconnect the front passenger’s airbag 4P connector (see step 2 ).

4. Disconnect the connectors from the front passenger’s weight sensor unit. Remove the mounting bolt

(A) and the front passenger’s weight sensor unit (B) from the seat riser.

NOTE:

Review the seat replacement procedure (see FRONT SEAT
REMOVAL/INSTALLATION ) before performing repair or service.

2007 Acura RL

2005-08 RESTRAINTS SRS (Supplemental Restraint System) — RL

me

Friday, June 05, 2009 2:21:59 PM

Page 304 © 2005 Mitchell Repair Information Company, LLC.

Fig. 430: Identifying Front Passenger’s Weight Sensor Unit And Fastener
Courtesy of AMERICAN HONDA MOTOR CO., INC.

INSTALLATION

1. Place the new front passenger’s weight sensor unit on the seat riser. Torque the mounting bolt (A), and

connect the connectors.

Fig. 431: Identifying Front Passenger’s Weight Sensor Unit And Fastener With Torque
Specifications

Courtesy of AMERICAN HONDA MOTOR CO., INC.

2. Reconnect the front passenger’s airbag 4P connector (see DISCONNECTING SYSTEM

CONNECTORS ).

3. Reconnect the negative cable to the battery.

4. Calibrate the front passenger’s weight sensor unit (see FRONT PASSENGER’S WEIGHT

SENSOR UNIT CALIBRATION ).

5. After installing the front passenger’s weight sensor unit, confirm proper system operation: Turn the

ignition switch ON (II); the SRS indicator should come on for about 6 seconds and then go off.

NOTE:

Be sure to install the harness wires so they are not pinched or interfering
with other parts.

2007 Acura RL

2005-08 RESTRAINTS SRS (Supplemental Restraint System) — RL

me

Friday, June 05, 2009 2:21:59 PM

Page 305 © 2005 Mitchell Repair Information Company, LLC.

PASSENGER’S AIRBAG CUTOFF INDICATOR ILLUMINATION BULB
TEST

1. Remove the passenger’s vent panel (see DRIVER’S VENT PANEL

REMOVAL/INSTALLATION ).

2. Push out the passenger’s airbag cutoff indicator from behind the passenger’s vent panel.

Fig. 432: Checking For Continuity Between No. 3 And No. 4 Terminals Of Indicator Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.

3. Disconnect the 6P connector (A) from the passenger’s airbag cutoff indicator (B).

4. Check for continuity between the No. 3 and No. 4 terminals of the indicator. If there is no continuity,

replace the bulb (C).

5. Reinstall the parts in the reverse order of removal.

NOTE:

Both illumination bulbs are connected in parallel. If there is continuity,
remove the upper, hazard switch illumination bulb, and recheck for
continuity. If there is no continuity, replace the lower, passenger’s
airbag cutoff indicator illumination bulb.

2007 Acura RL

2005-08 RESTRAINTS SRS (Supplemental Restraint System) — RL

me

Friday, June 05, 2009 2:21:59 PM

Page 306 © 2005 Mitchell Repair Information Company, LLC.

2005-08 ACCESSORIES AND EQUIPMENT

Audio System — RL

COMPONENT LOCATION INDEX

Fig. 1: Identifying Audio System Component Location (1 Of 2)
Courtesy of AMERICAN HONDA MOTOR CO., INC.

2007 Acura RL

2005-08 ACCESSORIES AND EQUIPMENT Audio System — RL

2007 Acura RL

2005-08 ACCESSORIES AND EQUIPMENT Audio System — RL

me

Friday, June 05, 2009 3:53:06 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

me

Friday, June 05, 2009 3:53:13 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Оцените статью
Инструкции по ремонту
Добавить комментарий