Acura RL. Instruction — page 248

YES — Troubleshooting is complete.

NO — Return to step 13 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and
recheck.

DTC P0766: Shift Solenoid Valve D Stuck OFF; DTC P0767: Shift Solenoid Valve D Stuck ON

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 4 ) through a strainer. Inspect the strainer for metal debris or excessive clutch

material.

Does the strainer have metal debris or excessive clutch material?

YES — Replace the transmission, then go to step 13.

NO — Replace the ATF (see step 6 ), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears, then

slow down to a stop.

6. Turn the ignition switch to LOCK (0). Repeat step 5, then go to step 7.

7. Monitor the OBD STATUS for P0766 or P0767 in the DTCs/Freeze Data in A/T Mode Menu for a

pass/fail.

Does the HDS indicate FAILED?

YES — Go to step 8.

NO — Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return
to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Select Shift Solenoid D in the Miscellaneous Test Menu, and check that shift solenoid valve D operates

with the HDS.

Is a clicking sound heard?

YES — Go to step 10.

NO — Replace shift solenoid valve D (see SHIFT SOLENOID VALVE TEST AND

NOTE:

Before you troubleshoot, record all freeze data and any on-board snapshot, and
review General Troubleshooting Information (see GENERAL
TROUBLESHOOTING INFORMATION ).

2007 Acura RL

2005-08 TRANSMISSION Automatic Transmission — RL

me

Friday, June 05, 2009 1:18:12 PM

Page 163

© 2005 Mitchell Repair Information Company, LLC.

REPLACEMENT ), then go to step 13.

10. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears, then

slow down to a stop.

11. Turn the ignition switch to LOCK (0). Repeat step 10, then go to step 12.

12. Monitor the OBD STATUS for P0766 or P0767 in the DTCs/Freeze Data in A/T Mode Menu for a

pass/fail.

Does the HDS indicate FAILED?

YES — Repair shift valve D, or replace the transmission, then go to step 13.

NO — Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return
to step 10 and recheck.

13. Clear the DTC with the HDS.

14. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears, then

slow down to a stop.

15. Turn the ignition switch to LOCK (0). Repeat step 14, then go to step 16.

16. Monitor the OBD STATUS for P0766 or P0767 in the DTCs/Freeze Data in A/T Mode Menu for a

pass/fail.

Does the HDS indicate PASSED?

YES — Troubleshooting is complete.

NO — Return to step 13 and recheck. If the HDS indicates NOT COMPLETED, return to step 14 and
recheck.

DTC P0776: A/T Clutch Pressure Control Solenoid Valve B Stuck OFF; DTC P0777: A/T Clutch Pressure Control
Solenoid Valve B Stuck ON

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 4 ) through a strainer. Inspect the strainer for metal debris or excessive clutch

material.

Does the strainer have metal debris or excessive clutch material?

YES — Replace the transmission, then go to step 11.

NOTE:

Before you troubleshoot, record all freeze data and any on-board snapshot, and
review General Troubleshooting Information (see GENERAL
TROUBLESHOOTING INFORMATION ).

2007 Acura RL

2005-08 TRANSMISSION Automatic Transmission — RL

me

Friday, June 05, 2009 1:18:12 PM

Page 164

© 2005 Mitchell Repair Information Company, LLC.

NO — Replace the ATF (see step 6 ), then go to step 4.

4. Clear the DTC with the HDS.

5. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears, then

slow down to a stop.

6. Turn the ignition switch to LOCK (0). Repeat step 5, then go to step 7.

7. Monitor the OBD STATUS for P0776 or P0777 in the DTCs/Freeze Data in A/T Mode Menu for a

pass/fail.

Does the HDS indicate FAILED?

YES — Go to step 8.

NO — Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return
to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Select Clutch Pressure Control (Linear) Solenoid B in the Miscellaneous Test Menu, and test A/T clutch

pressure control solenoid valve B with the HDS.

Does the HDS indicate NORMAL?

YES — Intermittent failure, the system is OK at this time.

NO — Follow the instructions indicated on the HDS by the test result, but if the HDS has not determined
the cause of the failure, go to step 10. If any part is replaced, go to step 11.

10. Inspect A/T clutch pressure control solenoid valve B (see A/T CLUTCH PRESSURE CONTROL

SOLENOID VALVE B TEST ).

Does A/T clutch pressure control solenoid valve B work properly?

YES — Repair the hydraulic system related with shift valve B, or replace the transmission, then go to step
11.

NO — Replace A/T clutch pressure control solenoid valve B (see A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE A AND B REPLACEMENT
), then go to step 11.

11. Clear the DTC with the HDS.

12. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears, then

slow down to a stop.

13. Turn the ignition switch to LOCK (0). Repeat step 12, then go to step 14.

14. Monitor the OBD STATUS for P0776 or P0777 in the DTCs/Freeze Data in A/T Mode Menu for a

pass/fail.

2007 Acura RL

2005-08 TRANSMISSION Automatic Transmission — RL

me

Friday, June 05, 2009 1:18:12 PM

Page 165

© 2005 Mitchell Repair Information Company, LLC.

Does the HDS indicate PASSED?

YES — Troubleshooting is complete.

NO — Return to step 11 and recheck. If the HDS indicates NOT COMPLETED, return to step 12 and
recheck.

DTC P0796: A/T Clutch Pressure Control Solenoid Valve C Stuck OFF; DTC P0797: A/T Clutch Pressure Control
Solenoid Valve C Stuck ON

1. Warm up the engine to normal operating temperature (the radiator fan comes on).

2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.

3. Drain the ATF (see step 4 ) through a strainer. Inspect the strainer for metal debris or excessive clutch

material.

Does the strainer have metal debris or excessive clutch material?

YES — Replace the transmission, then go to step 11.

NO — Replace the ATF (see step 6 ), then go to step 4.

4. Clear the DTC with the HDS.

5. Start the engine. With the brake pedal pressed, shift to D, and wait for at least 3 seconds. Shift to R, wait

for at least 3 seconds, then reverse the vehicle for at least 3 seconds. Slow down and stop the wheels.

6. Turn the ignition switch to LOCK (0). Repeat step 5, then go to step 7.

7. Monitor the OBD STATUS for P0796 or P0797 in the DTCs/Freeze Data in A/T Mode Menu for a

pass/fail.

Does the HDS indicate FAILED?

YES — Go to step 8.

NO — Intermittent failure, the system is OK at this time. If the HDS indicates NOT COMPLETED, return
to step 5 and recheck.

8. Clear the DTC with the HDS.

9. Select Clutch Pressure Control (Linear) Solenoid C in the Miscellaneous Test Menu, and test A/T clutch

pressure control solenoid valve C with the HDS.

Does the HDS indicate NORMAL?

NOTE:

Before you troubleshoot, record all freeze data and any on-board snapshot, and
review General Troubleshooting Information (see GENERAL
TROUBLESHOOTING INFORMATION ).

2007 Acura RL

2005-08 TRANSMISSION Automatic Transmission — RL

me

Friday, June 05, 2009 1:18:12 PM

Page 166

© 2005 Mitchell Repair Information Company, LLC.

Оцените статью
Инструкции по ремонту
Добавить комментарий